Testing cables at high voltages can help determine the presence of moisture, flux, or contaminants that may have penetrated the insulation or connector backshell breaks, and ensures that the insulation between wires can withstand temporary voltages higher than the normal working voltage offset without decomposing. The results of the high-voltage test usually show the insulation resistance between ...
[Terminal] Instructions for the use of heat shrinking tube in wire harness After the heat shrinking tube is encountered, it has a different role in fully automatic diameter and smaller. Therefore, the specifications of thermal shrinkage and thermal shrinkage are generally marked in A/B, that is, the inner diameter is AMM pipes, which can be gathered at least to gather together To BMM. The thermal ...
The high voltage connector for new energy vehicles is an integrated electromechanical product, which is mainly composed of contact parts, insulators, shells, and accessories. Among them, the contact part is the core component of the connector to complete the light and electrical signal connection. Complete the connection of light and telecommunications required for vehicles during driving; insulat...
Among the new energy vehicles (pure electric as an example) high voltage cable assemblies can be divided into 5 parts 1. Power battery high voltage cable: that is, the wiring bundle between the power battery and the high voltage box. 2. Motor controller cable: that is, the cable connecting the high voltage box to the motor controller. 3. Fast charging wire harness: connect the cable assembly ...
Foreword With the rapid development of Industry 4.0, the application scenarios of electrical connectors and sensors are increasing. As one of the key components of signal and data transmission, industrial cable assemblies also have strict requirements for signal transmission, on -site protection, and convenient installation. Accompanied by customers' demand for industrial cable assemblies, it is m...
What is a RF connector? The radio frequency connector is defined as: a separate component that is usually installed on a RF cable assemblies or device for the electrical connection of the transmission system. It can be seen from this definition that it has the common characteristics of the "separated element" connection. Taking the commonly used coaxial axis as an example, the main model of...
I. Ultrasonic welding principle: Ultrasonic wiring harness welding is a commonly used process of car wire welding. The principle is to re -combine the surface of the welding material through high frequency vibration. Ultrasonic welding energy consumption is low, no pollution, strong welding and low internal resistance, and does not change the chemical properties of welding parts. Welding cond...
1. Substrate requirements: No dirt Grease/oil free Dry During use, the following products cannot be used: Talcum powder Silicone Molding agent hand cream 2. When the tape is pulled from the tape roll: Do not store the tape in the way shown below. Do not touch the end of the tape with your fingers (with oil)! 3. The spool of tape is rolled close to the wire harness, and the tape cannot...
The European electric vehicle charging standard CCS2 is a combined standard that integrates AC charging and DC charging. The combined charging system is an open international standardized system, mainly promoted by Audi, BMW, Chrysler, Daimler, Ford, General Motors, Porsche and Volkswagen. Vehicles exported to Europe need to meet their physical interface and communication requirements. Euro...
The charging system can be divided into two methods: conventional charging and fast charging. From the perspective of appearance and size, the difference between the charging ports is actually very simple. The fast charging port is large and has 9 holes (two large holes, one middle hole, and 6 small holes). The slow charging port is small and has 7 holes (5 large holes and 2 small holes), so that ...
Connectors are used in every car. The device uses signals such as electricity and light to control the corresponding mechanical force to connect, disconnect, and convert, and then realizes a functional element of the corresponding circuit or optical channel conversion, and With the help of ECT electrical and optical signals, signal distortion and corresponding energy loss can be effectively preven...
When consumers are looking to purchase an EV, the time it takes to charge an EV continues to influence their purchasing decision. Today, the fastest way to charge an electric vehicle is high-power direct current (DC) fast charging. DC fast charging, unlike AC charging, requires specific OEM considerations when designing critical components of the vehicle's electrical architecture, such as charging...
once you subscribe our newsletter. we will keep you posted the latest catalog,Also will inform you the trendy news for the electronics and wire harness.