MC4 connector is a single contact electrical connector. They are usually used to connect solar wires to solar panels. MC4 stands for "multi contact, 4 mm". It is the standard of renewable energy industry. MC4 connector can easily build panel strings. In today's solar market, MC4 connectors and their compatible products are widely used. In most cases, larger solar panels are already equipped with M...

IDC cable assembly "The insulation displacement contact (IDC), also known as the insulation penetration contact (IPC), is an electrical connector designed to connect the conductors of insulated cables. Through the connection process, one or more blades that are selectively sharpened are forced to pass through the insulation without peeling off the insulation conductor before connection. When it is...

Ribbon cable (also known as multi wire flat cable) is a cable with many wires running in parallel on the same plane. Therefore, the cable is wide and flat. Its name comes from its similarity to a ribbon       Ribbon cables are usually used for internal and external devices of a computer, such as hard disk drives, CD drives, and floppy disk drives. In some older computer systems, suc...

SATA stands for Serial ATA. It is a type of computer bus that is mainly used for data transfer between the motherboard and mass storage devices such as hard disks and optical disk drives. This is a new type of hard disk interface completely different from serial PATAs, so named because of the serial mode of data transmission. SATA bus uses embedded clock signal, which has stronger error correction...

1. The voltage environment used is different. Eur-gauge power cords are used at 220V, while American gauge power cable usually work at 110V. 2. The core section of the US standard power cord is thicker than that of the European standard power cord. According to P=UI(P is the power, U is the voltage, and I is the current), the current passing through is higher because the working vol...

The BUSBAR design selection is not only as simple as considering the ability of overcurrent. Usually when designing a battery, the most considers is busbar, paying attention to its overcurrent ability and heat.   How do we judge when doing busbar design? It is a very important point to be warming. If we simply say how wide, how many layers thick, and how much the cross -sectional area, and th...

Among the new energy vehicles (pure electric as an example) high voltage cable assemblies can be divided into 5 parts 1. Power battery high voltage cable: that is, the wiring bundle between the power battery and the high voltage box. 2. Motor controller cable: that is, the cable connecting the high voltage box to the motor controller. 3. Fast charging wire harness: connect the cable assembly ...

I. Ultrasonic welding principle: Ultrasonic wiring harness welding is a commonly used process of car wire welding. The principle is to re -combine the surface of the welding material through high frequency vibration. Ultrasonic welding energy consumption is low, no pollution, strong welding and low internal resistance, and does not change the chemical properties of welding parts. Welding cond...

HV Cable selection 1. Cable diameter According to the layout diagram of each high-voltage electrical component of the vehicle, the main circuit and branch circuit are distinguished, and the responsible characteristics of the high-voltage components connected to the high-voltage wiring harness are determined. Characteristics include working voltage, rated power, peak power, rated current, peak curr...

The charging system can be divided into two methods: conventional charging and fast charging. From the perspective of appearance and size, the difference between the charging ports is actually very simple. The fast charging port is large and has 9 holes (two large holes, one middle hole, and 6 small holes). The slow charging port is small and has 7 holes (5 large holes and 2 small holes), so that ...

Connectors are used in every car. The device uses signals such as electricity and light to control the corresponding mechanical force to connect, disconnect, and convert, and then realizes a functional element of the corresponding circuit or optical channel conversion, and With the help of ECT electrical and optical signals, signal distortion and corresponding energy loss can be effectively preven...

In order for the robot to perform its tasks accurately and efficiently, there must be no errors in the various connections inside the robot. At this time, the crimping form of the Robot Wire Harness is very important, and we also need to be strict about it, and the crimping harness must be stable and reliable. With the continuous rise of labor costs, there are more and more occasions to use robots...